Search results

hey guys I think I have a bad ECU in this r6 2008 would like to test with a good one to make sure, anyone out there with a 2008 r6 ecu would like some dyno time in trade?

[SIZE="5"]This is a true hot rod project, James is not a paid mechanic, but with a great deal of passion and wanting to do it right, he built a very cool Bonneville speed bike, that at his first-time out, set a record. I'm proud BRG was able to help. This old bike a 1955 supercharged...

We have been doing a number of older bikes, when I say older, I mean 1990 or older, I thought it would be fun to do videos on what was needed to get some of these bikes back up and running and start a new Series entitled THIS OLD BIKE. This 1967 BSA Hornet had not been running in 5 or 6 years...

After the break-in tune and Brian got 1000 miles on the bike, he brought the bike back in to do what we call the finished tune, this is where we go through after the break-in and finalize are fueling and ignition timing, because in 90% of the time this changes, due to better ring seal and...

After the break-in tune and Brian got 1000 miles on the bike, he brought the bike back in to do what we call the finished tune, this is where we go through after the break-in and finalize are fueling and ignition timing, because in 90% of the time this changes, due to better ring seal and...

Here at BRG, we have done a lot of what I call cool projects. I thought it would be fun, in light of everyone being stuck in lockdown, and you all may be looking for stuff to check out, to post some of the videos I have made. My hope is you find them informational and fun, hopefully not...

In light of everyone on some kind of lockdown, I have a bunch of videos that I have done over the years, I thought I would post some of the funny ones and some of the cool bike projects we have done over the years. I hope there entertaining and not like watching someone’s home movies. Let me...

. BRG Motorsports is still open, we are ready to work on and do whatever maintenance your bike may need. We have pandemic proto calls in place. We ask if you can wear a mask for both our safety. If not we can supply you with one. Call first! So we can be set up for you when you come in...

[/SIZE]This is a project we did mid-summer for Tony P.. Tony had taken his old school VFR 750 and with some help from his friends turned this old school VFR into a very cool and very nimble Streetfighter. Nice Job Tony. :thumbup Hj-5cNRiMmU

-OXhpYcmBmI We finished up the Dyno tune and then the video on Matts "Z" very nicely restored 1983 CB1100f. I thought I should share it. Hope you all like it. We sure do. And if you need your bike worked on, we are open. we do have protocols in place you need to follow if you come in. Thanks ...

I haven’t been very active in the motorcycle community, for the last few years. Well recently I've been getting up on barf more, I've been sitting on the side reading some of the posts, and from what I can gather, BRG motorsports is thought of as a specialty shop. Where we only do top notice...

Hi Guys and Gals Being that I'm not very sharp, when it comes to al this Utube adds stuff. I could use some help getting up to speed on it. If you would like to trade some work / Dyno time, for helping me get better informed on UTube. PM me Thanks :thumbup K.C.

BRG Looking for a Drag Racer with good track record, to ride H2 I guys. Here is a short video of BRG Tuning an H2. Also a very special message at the end.:cool 7-WgJOvy9zY

Some more fun @ BRG Motorsports. The lastest BRG beast. A 2010 ZX 1400 :cool 4p9rDawYE58:cool

I signed up to watch the races online but I guess I'm not too bright cause I can figure out how to do it. can someone point me in the right direction?:nchantr

:cool Here is a heads up for the customers of Steve "Quickturn Cycles" Davis, fame in Concord. As you may know, or not know, Steve had some health issues that made him close his shop. People have been asking if Steve is coming back to the business of servicing and repairing motorcycles in the...

I need to borrow an ECU out of a 09 GSXR 600 to diagnose a bike in the shop. There is no risk to the ECU. I need it to verify a function. If you have one I can borrow for about 25Min PM me and I will do a baseline Dyno as payment for your let me use your ECU.:thumbup Thanks :ride K.C.

Hi All I haven't done 1 of these in a few years. Is there any interest on a Saturday. for a small fee, we do a Dyno Evaluation on how your bike is running and what can be done to make it better. :ride:thumbup

Spoiler alert!! over the years BRG has done some very cool projects. Here are just a few videos of them. We truly have a sickness for quickness If you need, service work or performance upgrades give us a call we can help .:thumbup D3C7TcmuvVk 130 HP A very fast stock R6 :teeth 4ioVjU3AAEM A...

Hi all I'm trying to find the rules coving the EX 400 in production class. Thanks all