Search results

WTB 2016+ iron 883 OEM Factory exhaust Or 2014+ iron 883 Vance and Hines exhaust (short shots preferred)

Does anyone know how easy it is to hook this up? I have a 2011 iron 883...

Hi All, I've purchased a 2012 GSXR 750 5k miles. Problem:Sometimes, I've noticed that there is some resistance coming from the front wheel when accelerating from a complete stop. It sounds like a little bit of rubbing. Data: When riding at 30+ mph, the bike seems to ride straight. I...

Hi Guys, I have a 2006 r6. The turn signals are not functioning properly. When I push the turn signal to the left and let go, the turn signal does not come on. When I push the turn signal to the left and hold, the turn signal comes on after about a 5 second delay. Note that I have to hold...

Hello. I am trying to adjust my valves on my gsxr600 k7. I cannot remove the journal holders. I removed the bolts in the descending order. However, the journal holders are not pulling off!! I've read that I should not use a pry bar or flat edge to try and lift the journal holders Any...

Got into a motorcycle accident yesterday. Can anyone help out with a tow before storage fees go over $1000. http://www.yelp.com/biz/red-line-towing-san-mateo?osq=redline+tow Ill pay $100!! Please let me know. 650-228-4704 Thank you, -Collin

Are you supposed to check the fluid in the front brake reservoir while the bike is on its side stand with the bar turned all the way to the left? Bike is a cbr600f4i.

My bike came with a leo vince slip on. However the mid-pipe does not have a hole for the o2 sensor. The previous owner zip tied the o2 sensor to the side of the subframe. I want to use the o2 sensor. Any recommendations on a muffler shop to drill a hole and weld a bung for my o2 sensor...

Any thoughts or reviews/experience on this air filter? http://www.ebay.com/itm/Honda-CBR600F4-OE-Factory-Stock-Style-Replacement-Air-Filter-17210-MBW-D20-/151275834214?pt=Motorcycles_Parts_Accessories&hash=item2338be0b66&vxp=mtr Or should I just get an OEM from the dealer. Part# 17210-MBW-D20

Looking for an OEM f4i front right turn signal Part # 33400-MBW-A10

How do I remove these type of connectors?

Where can I learn to control my motorcycle like this? http://www.youtube.com/watch?v=4B9L5XkPr0A

Hello, I can't tell if my o2 sensor is working or not. I just bought a 2001 cbr f4i and I found that the o2 sensor was just zip tied to the side because the previous owner installed an aftermarket exhaust without the hole in the midpipe for the o2 sensor. I removed the o2 eliminator plug and...

I want to return my bike back to stock height. I need an OEM dog bone for the f4i

I just bought an f4i, but it has been lowered. It looks like the forks have been slid up the triple clamp. Are there any good "how to's" to return the forks back to stock height? I have a pitbull triple tree stand, that should be all I need for the front right? Also, I can't tell if the rear...

Anyone in Davis that can help me adjust my chain? The manual say to loosen the rear axle nut before I adjust the chain but the wrench that the bike came with is very short and I can't loosen the nut!! Do I need a breaker bar or something?? : (

Both my my HID bulbs don't work. I've had these for about 4 months. I ordered them from DDM tuning. I do not know if the ballast or bulbs have gone bad. When I start the engine, the HID bulbs flicker, but do not turn on. At first I thought it was a wiring issue, but then I put in my halogen...

I've taken a look at the charging system thread and a fault finding flow chart I found on the web. The flow chart is located here: http://www.crowitis.com/images/fault_finding.pdf When I rev the engine to 5000 rpm, I'm getting 14.6 as my voltage. Which is in the range at in the fault finding...

Hello all! I'm about to buy an RK XSO X-Ring chain from a fellow barfer. http://bayarearidersforum.com/forums/showthread.php?t=405497 He has informed me that it is an endless chain with 108 links. Before I buy it, I was wondering if it is okay to cut one of the links and replace it with a...

Need to replace tires! I'm probably going to try and remove the wheels myself and have a shop mount the tires. I've also noticed some kinks in my chain so it probably needs to be replaced. I've read that I'm supposed to replace the sprockets along with the chain. What tools do I need? I have a...