Search results

Hi all. 2015 is coming to a close and it's time for the first round of elections. My term as rider rep is coming to a close and I've decided to run for the position that Dave Stanton is vacating. Dave is a huge asset to the club and a great guy, I hope to still lean on him for advice if I'm...

Hey all, here's a quick summary of the meeting at Buttonwillow. Keep in mind that these are not official minutes but rather my shorthand notes so don't hold freak out if the official minutes differ slightly. :) In the order that they were in on the agenda: 1 & 2 - No motion or discussion...

Comment below if you want to elaborate.

Hey all, The AFM is looking to upgrade its current start/finish camera and requires an iPhone 4 or newer to serve as a WiFi remote. If you have a surplus phone laying around and would like to help out the club please PM me or contact me via the Contacts page on the AFM web site. Thanks, Kyle...

Here's a little rundown of the meeting. Please be aware that these are my notes and not in any way official meeting minutes or an announcement by the AFM. - Red flag procedure has been updated to mirror what MotoAmerica and others do. - 9.1.6(r) has been updated to allow a wider selection of...

A number of members have requested that the board consider racing the final round at Buttonwillow in the counter clockwise direction. Several years ago, before we cut the second Buttonwillow round from the schedule, we did do this successfully. I'd appreciate a bit of feedback on the subject...

Hey guys and girls. I've accepted the nomination to run for the Rider Rep position being vacated by Lisa Kinberger (who did a great job, by the way). I've been involved with the club since late 2007, racing a few races here and there until 2012 when I had a successful run at 4 600 and 750...

Just a heads up, there will be a bicycle race running a clockwise loop on Pescadero, Stage and 84 tomorrow. Roads are open to all traffic but expect some delays while passing the groups. Please give us room when and if you do. :thumbup

Awesome shock. Valved for a 170ish pound rider by Fastbike Industries. Spring is a 1.0 but I can throw a .95 on it if that is preferred. Fluid is fresh, zero days of running on it. $950

Light rash on the stator cover and a couple of scratches that look more like garage/truck damage than crash damage on the timing cover. The blue sliders are replaceable with bolts from the inside so that they can't be ground down in a crash. $200.

These will fit, as is, a 2005-2013 R6. With a rotor swap they'll fit the 03-04 as well and any R6S. Wheels are true and rotors are straight. The front wheel is marked as being bent so it seems to have been repaired at some point as it's fine now. Minor scratches and dings from being in the...

Roost guard is a Fox Air Frame. I believe it's a Large but can't find a size on it. I'm 5'11" 170 and it fit well. Normal scratches and wear from about a season of riding but nothing broken on it. The back pack is a Fly Racing back pack and water pack combo that straps to the roost guard. It...

Gone!

Worked great. Selling the bike so I took some of the goodies off including this. $175. Pick up in San Jose near the Great Mall. PM if interested.

Penske 8760, sprung and valved for 170lb rider. These were the weapon of choice for this bike, worked awesome. Has a little surface rust on the spring collar from the bike sitting outside. $400. Pick up in San Jose near the Great Mall.

Morse brand, similar in quality/construction to Armour Bodies. These were crashed on. The bellypan has been patched and primered. The upper needs a little prep work as the old paint is chipping off in big pieces. No hardware included. $40. Pick up in San Jose near the Great Mall.

Dented but does not leak, worked fine when it was on the bike. $25 or $75 with the fuel pump. Pick up in San Jose near the Great Mall.

In good condition. The bags are wearing a little thin but the chairs themselves are not. The one on the left is a straggler, doesn't have a bag. $20 for the set. Pick up in San Jose near the Great Mall.

Picked this up on sale a few years back for a couple of small projects around the house. Once they were done I boxed it back up an into storage it went. Worked perfectly for what I needed it to do. Blade should still have plenty of life left. $75...

I'm looking for a T20 bit or socket with a length of 4-6". A short bit in a longer holder won't do, the hole that the screws sit in are too narrow for it to fit. I know that they're sold around the web including McMaster but I don't won't to throw $10 shipping at a $5 bit. Does anyone have one...