Recent content by GreenMagic

Hi If you happen to have any of these parts let me know! 1993-2005 Kawasaki ZX6E (not the R or RR) / Ninja ZX-6 models are all the same. 2004-2005 they were called ZZR600 for some odd reason. - left rear turn signal / blinker. The 'integrated' into fairing type - nose front fairing - either...

Ninja ZX6R shock spring. ZX6R spring Spring O.D. Outside diameter = 3.25" Come from very low mileage ZX6R. It was replaced with a racing shock and this spare was traded to me.

Hi I have a Ninja ZX6E specifically but many Kawasaki parts should fit. I need the lever end itself, which likely has a riveted in pivot and attachment that then is bolted on to the longer shaft that goes to the gearbox. Just need the part that the toe touches / shifts. I crashed 14 months ago...

Hi all Long shot here: MY Vehicle WAS STOLEN, Yesterday, Sunday July 24th, 2016 between 1:30 and 5 pm my full size cargo van (and home on the road) was stolen from it's normal legal parking spot in a nice residential spot in Oakland. Not parked in downtown but in the nicer hills area. This is...

Recently got a CNG a van. Didn't know much about CNG. Ran it out of CNG fuel last night driving a little out of Bay Area and known fueling stations. went to multiple locations and they didn't have 3000 psi stuff I need. Had to get towed back to Stockton PGE CNG natural gas station at 4040 N...

Many parts for Kawasaki ZX6 E Ninja (600) parts for sale: Fits: 1993 - 2004 ZX6 E models - ALL and certain early ZZR 600 2004 2005 models. Some may fit the '91 - '93 'D' Model as well and some ZZR1100, ZX6R, ZX9R, ZX10R, Versys, Concours models for certain parts. - set of carbs. All four carb...

Hi. I have a Kawasaki EX500 owners manual book. Very nice shape. Free to anyone who can use it. Thanks, GMM Also non moto for free: I also have a Led Zep Physical Graffiti Vinyl LP Great Britain tour guide book VGA to VGA cable red white yellow RCA cable (2) headlamps. they take CR2025...

Hi all: Sticking a toe cautiously in the water to see if there might be any interest in a ride on Thanksgiving Day and / or maybe a meal somewhere as a small group (or large)? First post in group rides. Might be botching protocol, not sure. I'm in the East Bay / Oakland but doesn't matter for...

The Kawasaki ZX6E model was sold from '93 - '04 and a lot of people inquire about modifying it to look different. I'm going to post up some pics here of different modifications that have been done by various owners, and one project that I will be undertaking next week on my ZX6E. I have an...

I cannot say I am enjoying this particular job. Firstly I wasted several hours lining the timing marks up wrong. My digital Haynes copy timing mark photo is completely illegible. And all I could find online was ZX6R and other Kwawk instructions so I thought I was supposed to line up 1/4 and 2/3...

Hi all: Been having a fuel leak for quite some time. Both main tank and tank to fuel pump lines get wet on long rides, gunk build up on subframe below... Bought a K & L fuel tap rebuilt kit # 18-2728 The parts look identical. However, the main O ring that goes around the selector / spinning...

Runs great! Starts right up easily every time, purrs perfectly. I have run this pretty regularly mostly on the weekend in the countryside / hills. Does not burn oil. Air cooled motor so no coolant / maintenance worries. Clean title and CA current registration good through May 2016. Starting...

exhaust stud bolt Honda '78-'86 400 / 450cc twin motor. 6mm x 65mm double thread 1.00 pitch NEEDED! Anyone have old Honda parts / parts motor / parts bikes kicking around?? I snapped one last night and need to get this running today. No one stocks one - all special order 3-5 day wait of...

exhaust stud bolt Honda '78-'86 400 / 450cc twin motor. 6mm x 65mm double thread 1.00 pitch NEEDED! Anyone have old Honda parts / parts motor / parts bikes kicking around?? I snapped one last night and need to get this running today. No one stocks one - all special order 3-5 day wait of...

Hi: I have a 1978 CB400A engine top end torn apart currently. I had to fix a massive oil leak in the cylinder to crankcase gasket (was a major tear due to way too much crank pressure due to double the amount of oil in the crank!) Anyway, got a BRM Flex-Hone tool. It's the 3" size one. The I.D...